zonealarm configuration

zonealarm configuration

Secure Home | Search | About
 Networking Firewalls    Post an article   get this group's latest topics as an RSS feed add this group's latest topics to your My MSN content add this group's latest topics to your My Yahoo content add this group's latest topics to your Google content
Subject Author Date
zonealarm configuration nospam 01-03-2006
Posted by nospam on January 3, 2006, 2:44 pm
If you were  Registered and logged in, you could reply and use other advanced thread options
Hi,

Zonealarm 6.1.737.000

I have two computer connected to an ADSL WiFi router, they can both
access the internet OK through the router.

I am trying to set up zone alarm to enable my laptop to get access to
the desktop.

What is the best way to set up the Zonealarm firewall on my desktop
(win2k) to allow access from my laptop (win XP)?


The IP address allocated from the ADSL WiFi router to the laptop could
be from

10.0.0.0 (or is it 10.0.0.1)

to

10.0.0.255 (I think)

should I configure using an IP range (10.0.0.0 - 10.0.0.255)

or a sub net (10.0.0.0/255.255.255.0)?

What zone should I pick for it, trusted or internet?

Thanks


Posted by Jim on January 3, 2006, 7:58 pm
If you were  Registered and logged in, you could reply and use other advanced thread options

> Hi,
>
> Zonealarm 6.1.737.000
>
> I have two computer connected to an ADSL WiFi router, they can both access
> the internet OK through the router.
>
> I am trying to set up zone alarm to enable my laptop to get access to the
> desktop.
Have you enabled ICMP packets?
>
> What is the best way to set up the Zonealarm firewall on my desktop
> (win2k) to allow access from my laptop (win XP)?
>
>
> The IP address allocated from the ADSL WiFi router to the laptop could be
> from
>
> 10.0.0.0 (or is it 10.0.0.1)
>
> to
>
> 10.0.0.255 (I think)
Could be much more. The entire 10.x.x.x range is not routable.
>
> should I configure using an IP range (10.0.0.0 - 10.0.0.255)
No, you need to leave an IP for the router. The range is usually
10.0.0.100 - 10.0.0.255. As I have only two computers, I used the addresses
that the router gave them.
You could also use the computer names.

>
> or a sub net (10.0.0.0/255.255.255.0)?
I didn't need to specify the mask.
>
> What zone should I pick for it, trusted or internet?
Trusted. You do trust your laptop don't you? Besides, that is what the
instructions state.
Jim
>
> Thanks
>



Similar ThreadsPosted
PIX 501 Configuration Help May 27, 2006, 11:31 pm
Re: PIX Configuration Help ! August 30, 2006, 3:49 pm
need help with configuration January 31, 2007, 8:47 am
VPN/DMZ configuration help June 15, 2007, 7:53 am
NAT Device Configuration February 21, 2005, 5:27 pm
Network configuration.... June 28, 2005, 2:45 pm
IPSO configuration March 14, 2006, 9:09 am
Cisco IOS ACL Configuration May 9, 2006, 11:50 am
Moving configuration best way !! May 13, 2006, 1:59 pm
OutPost configuration July 23, 2006, 3:44 am

The site map in XML format XML site map

Contact Us | Privacy Policy