|
Posted by Jono on February 29, 2008, 11:44 am
If you were Registered and logged in, you could reply and use other advanced thread options
Hello Lists,
Help required setting up a remote access vpn using PIX 501 ios 6.1 (4)
and cisco vpn clients version 4 .6 and above. I have used the
following config, yet am getting no response from peer when attempting
the vpn connection from a client - can some one please point out the
obvious to me as i have very limited experience using Pix VPN:
Building configuration...
: Saved
:
PIX Version 6.1(4)
nameif ethernet0 outside security0
nameif ethernet1 inside security100
enable password BreEjXKPBNBYOIzY encrypted
passwd BreEjXKPBNBYOIzY encrypted
hostname ******
domain-name *******
fixup protocol ftp 21
fixup protocol http 80
fixup protocol h323 1720
fixup protocol rsh 514
fixup protocol rtsp 554
fixup protocol smtp 25
fixup protocol sqlnet 1521
fixup protocol sip 5060
fixup protocol skinny 2000
names
access-list fromoutside permit icmp any any
access-list fromoutside permit tcp any host a.b.c.d eq smtp
access-list fromoutside permit tcp any host a.b.c.d eq 3389
access-list fromoutside permit tcp any host a.b.c.d eq 5081
access-list fromoutside permit tcp any host a.b.c.d eq 3389
access-list fromoutside permit tcp any host a.b.c.d eq www
access-list fromoutside permit tcp any host a.b.c.d eq www
access-list 101 permit ip 10.0.0.0 255.255.255.0 10.99.0.0
255.255.255.0
access-list 101 permit ip 10.1.1.0 255.255.255.0 10.99.0.0
255.255.255.0
pager lines 24
interface ethernet0 10baset
interface ethernet1 10baset
mtu outside 1500
mtu inside 1500
ip address outside a.b.c.d 255.255.255.248
ip address inside 10.0.0.254 255.255.255.0
ip audit info action alarm
ip audit attack action alarm
ip local pool ippool 10.99.0.1-10.99.0.40
pdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 0 access-list 101
nat (inside) 1 0.0.0.0 0.0.0.0 0 0
static (inside,outside) a.b.c.d 10.0.0.2 netmask 255.255.255.255 0 0
static (inside,outside) a.b.c.d 10.0.0.145 netmask 255.255.255.255 0 0
access-group fromoutside in interface outside
route outside 0.0.0.0 0.0.0.0 a.b.c.d 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 rpc 0:10:00 h323
0:05:00 sip 0:30:00 sip_media 0:02:00
timeout uauth 0:05:00 absolute
aaa-server TACACS+ protocol tacacs+
aaa-server RADIUS protocol radius
no snmp-server location
no snmp-server contact
snmp-server community public
no snmp-server enable traps
floodguard enable
sysopt connection permit-ipsec
no sysopt route dnat
crypto ipsec transform-set myset esp-des esp-md5-hmac
crypto dynamic-map dynmap 10 set transform-set myset
crypto map mymap 10 ipsec-isakmp dynamic dynmap
crypto map mymap interface outside
isakmp enable outside
isakmp identity address
isakmp client configuration address-pool local ippool outside
isakmp policy 10 authentication pre-share
isakmp policy 10 encryption des
isakmp policy 10 hash md5
isakmp policy 10 group 2
isakmp policy 10 lifetime 86400
vpngroup remote address-pool ippool
vpngroup remote dns-server 10.0.0.2
vpngroup remote default-domain a.b.c.d.local
vpngroup remote split-tunnel 101
vpngroup remote idle-time 1800
vpngroup remote password ********
telnet 0.0.0.0 0.0.0.0 inside
telnet timeout 60
ssh 0.0.0.0 0.0.0.0 outside
ssh timeout 5
terminal width 80
Cryptochecksum:c8c0dd8e00a3c69fc1b133c04a54e0e5
: end
[OK]
Am happy to post "sh" commands if required.
Any help with regards the VPN is appreciated, also other pointers
along the way can only assist.
TIA
J
| 
XML site map