|
Posted by Dick Seed on October 19, 2007, 11:45 pm
If you were Registered and logged in, you could reply and use other advanced thread options
Mr Rojas
I'm going to assume that since it's been just under a year since I sent you
panels for unlocking, and I haven't gotten them back, that you will not be
doing the job and therefore have not fullfilled you end of our contract. Am
I to start making plans to recoup the price of my panels through legal
process? It really is too bad, your service that is.
|
|
Posted by Jim Rojas on October 19, 2007, 11:50 pm
If you were Registered and logged in, you could reply and use other advanced thread options
RLB is the only mind reader here. Which panels did you send in?
Jim Rojas
(813) 884-6335
Dick Seed wrote:
> Mr Rojas
>
> I'm going to assume that since it's been just under a year since I sent you
> panels for unlocking, and I haven't gotten them back, that you will not be
> doing the job and therefore have not fullfilled you end of our contract. Am
> I to start making plans to recoup the price of my panels through legal
> process? It really is too bad, your service that is.
>
>
|
|
Posted by Robert L Bass on October 19, 2007, 11:54 pm
If you were Registered and logged in, you could reply and use other advanced thread options > RLB is the only mind reader here...
Unfortunately, there's not much to read. :^)
--
Regards,
Robert L Bass
=============================>
Bass Home Electronics
941-925-8650
4883 Fallcrest Circle
Sarasota · Florida · 34233
http://www.bassburglaralarms.com
=============================>
|
|
Posted by TeraNews on October 22, 2007, 11:37 am
If you were Registered and logged in, you could reply and use other advanced thread options
Dick Seed isn't the only one with this problem. I suspect the Jim has bigger
concerns right now, but when I sent a board for unlocking, Brinks was not an
issue.
Yes, the check was cashed within a week or two of sending the board. And
yes, a business card with return address was securely attached to the board.
I've since written off the board as lost, but have discovered a way to
default NAPCO panels. Change the EPROM and then let the processor re-flash
the default code into the new EPROM. This seems to work very well. Haven't
tried with any other manufacturer. New EPROMS cost about $5.00 and can be
found on eBay. One needs skill in PC board repair and this should not be
attempted without the proper tools.
"Jim Rojas" <jrojas+tech-man.com> wrote in message
> RLB is the only mind reader here. Which panels did you send in?
>
> Jim Rojas
> (813) 884-6335
>
>
>
>
> Dick Seed wrote:
>> Mr Rojas
>>
>> I'm going to assume that since it's been just under a year since I sent
>> you panels for unlocking, and I haven't gotten them back, that you will
>> not be doing the job and therefore have not fullfilled you end of our
>> contract. Am I to start making plans to recoup the price of my panels
>> through legal process? It really is too bad, your service that is.
--
Posted via a free Usenet account from http://www.teranews.com
|
|
Posted by alarman on October 22, 2007, 4:35 pm
If you were Registered and logged in, you could reply and use other advanced thread options > I've since written off the board as lost, but have discovered a way to
> default NAPCO panels. Change the EPROM and then let the processor
> re-flash the default code into the new EPROM. This seems to work
> very well. Haven't tried with any other manufacturer. New EPROMS cost
> about $5.00 and can be found on eBay. One needs skill in PC board
> repair and this should not be attempted without the proper tools.
Wouldn't it be easier and safer to just replace the board?
--
js
- The bigger they are, the harder they fall.
( Also, the harder they bite, punch, and kick.)
|
| Similar Threads | Posted | | techman panel unlocking | July 1, 2007, 10:58 pm |
| Jim Rojas "panel unlocking" | August 16, 2007, 6:50 pm |
| Unlocking Vista 15P3 (Monitronics Boards) | October 12, 2007, 2:45 am |
| Tech-Man !!!!! | October 28, 2006, 6:34 pm |
| DSC Tech | August 17, 2007, 10:13 pm |
| Tech Support | September 12, 2005, 9:28 pm |
| PR: Brinks vs. Tech-man.com | October 28, 2006, 10:55 pm |
| Tech Help! For Windows | June 30, 2007, 10:35 am |
| DSC tech support | August 7, 2007, 10:40 pm |
| Tech-Man going to Texas? | October 12, 2007, 8:20 pm |
|
XML site map