|
Posted by blueman on March 28, 2006, 4:58 pm
If you were Registered and logged in, you could reply and use other advanced thread options
We have a DMP XR200L based wired alarm system consisting currently of
smokes, door/window sensors, and motion sensors.
I would like to add a water sensor in the basement and at least one
temperature sensor.
I would like the temperature sensor to be small and unobtrusive yet
adjustable if possible.
Any suggestions on brands and models to consider that would be
compatible and consistent with my alarm system.
Thanks
|
|
Posted by Robert L Bass on March 28, 2006, 5:44 pm
If you were Registered and logged in, you could reply and use other advanced thread options
Winland Electronics makes an environmental alert system called EnviroAlert that
will do what you want . I sell their products online. Here's a link to their
website. My URL is in my tag line below.
http://www.winland.com/security/products.php?category_id=5
--
Regards,
Robert L Bass
Bass Burglar Alarms
The Online DIY Store
http://www.BassBurglarAlarms.com
--
Never underestimate the power of very stupid people in large groups.
> We have a DMP XR200L based wired alarm system consisting currently of
> smokes, door/window sensors, and motion sensors.
>
> I would like to add a water sensor in the basement and at least one
> temperature sensor.
>
> I would like the temperature sensor to be small and unobtrusive yet
> adjustable if possible.
>
> Any suggestions on brands and models to consider that would be
> compatible and consistent with my alarm system.
>
> Thanks
|
|
Posted by Crash Gordon on March 28, 2006, 10:11 pm
If you were Registered and logged in, you could reply and use other advanced thread options
one RLB posted) - you will need to program & wire it in it in the panel
correctly. I usually program them as Aux response zones in DMP
panels...you'll eat up 2 zones one for hi temp one for low.
You'll need 5 conductors... +/- power, and three conductors for the loops if
using both the high and low temp...one high, one low, one common.
| We have a DMP XR200L based wired alarm system consisting currently of
| smokes, door/window sensors, and motion sensors.
|
| I would like to add a water sensor in the basement and at least one
| temperature sensor.
|
| I would like the temperature sensor to be small and unobtrusive yet
| adjustable if possible.
|
| Any suggestions on brands and models to consider that would be
| compatible and consistent with my alarm system.
|
| Thanks
|
|
|
Posted by Frank Olson on March 28, 2006, 10:50 pm
If you were Registered and logged in, you could reply and use other advanced thread options
> DMP doesn't need a special model of temp sensor, the Winland is fine (the
> one RLB posted) - you will need to program & wire it in it in the panel
> correctly. I usually program them as Aux response zones in DMP
> panels...you'll eat up 2 zones one for hi temp one for low.
>
> You'll need 5 conductors... +/- power, and three conductors for the loops if
> using both the high and low temp...one high, one low, one common.
Quick question about DMP (you'll catch on to the reason). Are the
"common" zone terminals at the same potential as the negative aux power?
If this is the case, then you'll only need four conductors to hook up
high and low temps.
Frank Olson
http://www.yoursecuritysource.com
|
|
Posted by Crash Gordon on March 29, 2006, 5:31 am
If you were Registered and logged in, you could reply and use other advanced thread options
expansion card zones, or expansion keypad zones...so I'd not do it with 4
conds.
| Crash Gordon wrote:
| > DMP doesn't need a special model of temp sensor, the Winland is fine
(the
| > one RLB posted) - you will need to program & wire it in it in the panel
| > correctly. I usually program them as Aux response zones in DMP
| > panels...you'll eat up 2 zones one for hi temp one for low.
| >
| > You'll need 5 conductors... +/- power, and three conductors for the
loops if
| > using both the high and low temp...one high, one low, one common.
|
|
| Quick question about DMP (you'll catch on to the reason). Are the
| "common" zone terminals at the same potential as the negative aux power?
| If this is the case, then you'll only need four conductors to hook up
| high and low temps.
|
| Frank Olson
| http://www.yoursecuritysource.com
|
| Similar Threads | Posted | | Recommended Temperature & Water sensors for use with DMP-XR200 panel? | October 27, 2005, 2:39 pm |
| Re: What's up with our water? | March 10, 2008, 6:48 pm |
| Re: What's up with our water? | March 10, 2008, 6:49 pm |
| Ademco 50p: Water Flow Recommendations | December 26, 2005, 5:39 pm |
| Re: electrical wiring/hot water ground | May 13, 2007, 8:12 am |
| temperature monitor | September 26, 2005, 4:28 pm |
| Temperature Concerns | March 22, 2007, 12:10 pm |
| False alarm due to temperature???? | January 3, 2008, 10:25 am |
| Burglar Alarm Alerts to Reduce Water Damage | October 28, 2005, 8:37 am |
| Camera Suggestions | June 30, 2005, 10:02 am |
|
XML site map