Scantronic 500r+ reset tamper

Scantronic 500r+ reset tamper
Secure Home | Search | About
Login Password
Register Now! Lost Password?
 CCTV, Alarms and other Physical Security    Post an article   get this group's latest topics as an RSS feed add this group's latest topics to your My MSN content add this group's latest topics to your My Yahoo content add this group's latest topics to your Google content
Subject Author Date
Scantronic 500r+ reset tamper MyKey 04-11-2007
Posted by MyKey on April 11, 2007, 8:59 am
If you were  Registered and logged in, you could reply and use other advanced thread options
Can any alarm gurus out there help a noob out. I've accidently
(stupidly) set off a tamper alarm by removing a detector from the
wall. How can I reset the detector etc? The user manual says contact
engineer for service, but I've no idea who installed the alarm. I have
a copy of the installation and user guide but need some help to find
the correct command. Do I need a special engineer code?

Thanks in advance
Mike


Posted by GROUP MODERATOR on April 11, 2007, 9:04 am
If you were  Registered and logged in, you could reply and use other advanced thread options

> Can any alarm gurus out there help a noob out. I've accidently
> (stupidly) set off a tamper alarm by removing a detector from the
> wall. How can I reset the detector etc? The user manual says contact
> engineer for service, but I've no idea who installed the alarm. I have
> a copy of the installation and user guide but need some help to find
> the correct command. Do I need a special engineer code?
>
> Thanks in advance
> Mike

usually just put the cover back on and enter you code once or twice to
clear. or arm and disarm to clear depending on which system you have.



Posted by Jim on April 11, 2007, 11:36 am
If you were  Registered and logged in, you could reply and use other advanced thread options
> Can any alarm gurus out there help a noob out. I've accidently
> (stupidly) set off a tamper alarm by removing a detector from the
> wall. How can I reset the detector etc? The user manual says contact
> engineer for service, but I've no idea who installed the alarm. I have
> a copy of the installation and user guide but need some help to find
> the correct command. Do I need a special engineer code?
>
> Thanks in advance
> Mike

I stupidly pulled a plug apart in the engine compartment of my car.
How can I reset the check engine light on the dash board. The manual
says to bring it to my mechanic, but I don't have a mechanic. I have a
copy of the users guide but need some help to find the correct
command. Do I need a special engineer code?

Duuuuuuuuuh Would it help to know what make model and year, my car is?
Duuuuuuu ...... HuH? HUH? Would it?


Posted by GROUP MODERATOR on April 11, 2007, 12:01 pm
If you were  Registered and logged in, you could reply and use other advanced thread options

>> Can any alarm gurus out there help a noob out. I've accidently
>> (stupidly) set off a tamper alarm by removing a detector from the
>> wall. How can I reset the detector etc? The user manual says contact
>> engineer for service, but I've no idea who installed the alarm. I have
>> a copy of the installation and user guide but need some help to find
>> the correct command. Do I need a special engineer code?

unhook the battery for a few minutes then hook back up



Posted by Paul Ekins on April 11, 2007, 4:18 pm
If you were  Registered and logged in, you could reply and use other advanced thread options
purely from memory, I don't think the 500r needs eng code to reset a tamper.
You should be able to reset with the user code. Make sure the detector cover
is secured properly and it should transmit back to the panel. If after a few
attempts this doesn't work I would advise you replace the battery in the
detector. (yes the 500r is a radio panel)

good luck


A fine is a tax for doing wrong. A tax is a fine for doing well.

--
Paul Ekins

Linc Secure
Ph: 0845 123 2599
paul@lincsecure.co.uk
www.lincsecure.co.uk


> Can any alarm gurus out there help a noob out. I've accidently
> (stupidly) set off a tamper alarm by removing a detector from the
> wall. How can I reset the detector etc? The user manual says contact
> engineer for service, but I've no idea who installed the alarm. I have
> a copy of the installation and user guide but need some help to find
> the correct command. Do I need a special engineer code?
>
> Thanks in advance
> Mike
>



Similar ThreadsPosted
Scantronic 9800 bF every 5 minutes July 15, 2006, 4:07 pm
Scantronic 9800 rr code September 2, 2006, 7:01 am
Scantronic 9100 fault March 30, 2008, 3:24 pm
Scantronic 9800 Installation Manual July 5, 2006, 9:06 am
Scantronic 9800 BF Error message March 21, 2007, 8:06 am
Changing the chime on a Scantronic SP750 March 22, 2008, 10:02 am
Scantronic 9751 internal sounder/fire detector September 8, 2006, 5:46 am
Need to change access code for Scantronic Spartan sp750 December 28, 2006, 1:05 pm
Tamper Contacts October 15, 2005, 6:18 pm
Veritas R8 - tamper November 17, 2005, 3:46 pm

The site map in XML format XML site map

Contact Us | Privacy Policy