|
Posted by on April 4, 2007, 9:28 pm
If you were Registered and logged in, you could reply and use other advanced thread options
I got a "check 70" displayed on a Honeywell 6150 fixed english keypad.
I went over the manual, program sheet but don't have the keypad
literature. The central got the trouble signal and the restore when I
reset the keypad when I finished the repairs.
Equipment list:
Ademco Vista 20se
4229 expander
System Sensor 2 wire smokes
IEI Glass break detectors (audio)
6150 keypad
All zones hardwired.
I had the system powered down while I cleaned all the smokes (3).
Then I repaired 2 burg zones with breaks.
Anyone know what a check 70 trouble is?
Thanks
Roger W.
|
|
Posted by Crash Gordon on April 4, 2007, 9:49 pm
If you were Registered and logged in, you could reply and use other advanced thread options
Bell supervision trouble...check your siren/bell wiring...or just see if the
siren/bell runs.
|I got a "check 70" displayed on a Honeywell 6150 fixed english keypad.
| I went over the manual, program sheet but don't have the keypad
| literature. The central got the trouble signal and the restore when I
| reset the keypad when I finished the repairs.
|
| Equipment list:
|
| Ademco Vista 20se
| 4229 expander
| System Sensor 2 wire smokes
| IEI Glass break detectors (audio)
| 6150 keypad
| All zones hardwired.
|
| I had the system powered down while I cleaned all the smokes (3).
| Then I repaired 2 burg zones with breaks.
|
| Anyone know what a check 70 trouble is?
|
| Thanks
|
| Roger W.
|
|
|
Posted by Robert L Bass on April 4, 2007, 10:18 pm
If you were Registered and logged in, you could reply and use other advanced thread options > Bell supervision trouble...check your
> siren/bell wiring...or just see if the
> siren/bell runs.
True. Also, if the red jumper has been
cut the gentleman will need a 1K-Ohm
EOL resistor across the siren terminals.
The factiry default (jumprt uncut) is an
unsupervised output.
Note to newbies: Do NOT install the EOL
resistor inside the panel. Place it at the
siren location.
--
Regards,
Robert L Bass
=============================>
Bass Home Electronics
941-925-8650
4883 Fallcrest Circle
Sarasota · Florida · 34233
http://www.bassburglaralarms.com
=============================>
|
|
Posted by on April 4, 2007, 10:23 pm
If you were Registered and logged in, you could reply and use other advanced thread options
> Bell supervision trouble...check your siren/bell wiring...or just see if the
> siren/bell runs.
>
Thanks. I never thought to look in the Addendum sheet dated 2/98 until
you mentioned it. Yep, there it is. CHECK 70. Trouble is I never cut
that jumper or connected a 2k resistor to the speaker. I know I'm
senile but not that bad.......yet. I must have shorted something when
I disconected the power to the driver.Thanks again, Crash.
Roger W.
|
|
Posted by Crash Gordon on April 5, 2007, 12:53 am
If you were Registered and logged in, you could reply and use other advanced thread options
| wrote:
| > Bell supervision trouble...check your siren/bell wiring...or just see if
the
| > siren/bell runs.
| >
|
|
| Thanks. I never thought to look in the Addendum sheet dated 2/98 until
| you mentioned it. Yep, there it is. CHECK 70. Trouble is I never cut
| that jumper or connected a 2k resistor to the speaker. I know I'm
| senile but not that bad.......yet. I must have shorted something when
| I disconected the power to the driver.Thanks again, Crash.
|
| Roger W.
|
|
| Similar Threads | Posted | | Sanity Check Please | July 22, 2005, 7:30 am |
| YPE ***Hot stuff - check this out !!! YPE | January 28, 2006, 12:37 pm |
| Background Check | August 24, 2006, 5:20 pm |
| Check e-mail | May 17, 2006, 12:16 am |
| Frank-check e-mail | August 3, 2005, 3:31 am |
| Check out this Fire Eqpt. Collection | December 21, 2007, 7:00 am |
| Check Out NastyBurger Improved Site! | February 24, 2008, 2:06 am |
| Keypad says "check"- can't figure out what's wrong | March 16, 2008, 1:52 pm |
| Har! Check out this awesome Christmas trip... | November 29, 2008, 7:24 pm |
| Error check list for GEM-P9600 codes | April 1, 2007, 6:10 pm |
|
XML site map