Aritech Attender

Aritech Attender
Secure Home | Search | About
Login Password
Register Now! Lost Password?
 CCTV, Alarms and other Physical Security    Post an article   get this group's latest topics as an RSS feed add this group's latest topics to your My MSN content add this group's latest topics to your My Yahoo content add this group's latest topics to your Google content
Subject Author Date
Aritech Attender Bob Worthy 08-29-2005
Posted by Bob Worthy on August 29, 2005, 5:43 pm
If you were  Registered and logged in, you could reply and use other advanced thread options
Status light is flashing. I am assuming this is showing a bypassed zone (?).
How do I get the caller to get this panel back to a solid ready light.
System arms and disarms and all else seems normal accept the front door does
not trigger. Again, I am assuming zone 1 is bypassed or am I assuming
incorrectly? Thanks in advance.

Bob W.




Posted by Crash Gordon on August 29, 2005, 9:12 pm
If you were  Registered and logged in, you could reply and use other advanced thread options
Bypassed zones usually drop out once the system is armed then disarmed..have
you had them try to arm fully then disarm it?



> Status light is flashing. I am assuming this is showing a bypassed zone
> (?).
> How do I get the caller to get this panel back to a solid ready light.
> System arms and disarms and all else seems normal accept the front door
> does
> not trigger. Again, I am assuming zone 1 is bypassed or am I assuming
> incorrectly? Thanks in advance.
>
> Bob W.
>
>
>




Posted by Bob Worthy on August 30, 2005, 7:08 am
If you were  Registered and logged in, you could reply and use other advanced thread options

Yup..everything seems to be operating OK. Can arm, disarm, and other
openings register except the front door. Blinking status light remains.

Bob W.

> Bypassed zones usually drop out once the system is armed then
disarmed..have
> you had them try to arm fully then disarm it?
>
>
>
> > Status light is flashing. I am assuming this is showing a bypassed zone
> > (?).
> > How do I get the caller to get this panel back to a solid ready light.
> > System arms and disarms and all else seems normal accept the front door
> > does
> > not trigger. Again, I am assuming zone 1 is bypassed or am I assuming
> > incorrectly? Thanks in advance.
> >
> > Bob W.
> >
> >
> >
>
>




Posted by on August 30, 2005, 1:06 pm
If you were  Registered and logged in, you could reply and use other advanced thread options
The status light will also flash if the panel loses power or has a low
battery or fails to communicate or a fire zone has a fault. If the zone is
bypassed simply unbypass it.
The instructions for keypad operation are on the inside of the door.

> Status light is flashing. I am assuming this is showing a bypassed zone
> (?).
> How do I get the caller to get this panel back to a solid ready light.
> System arms and disarms and all else seems normal accept the front door
> does
> not trigger. Again, I am assuming zone 1 is bypassed or am I assuming
> incorrectly? Thanks in advance.
>
> Bob W.
>
>




Posted by Bob Worthy on August 30, 2005, 10:55 am
If you were  Registered and logged in, you could reply and use other advanced thread options

> The status light will also flash if the panel loses power or has a low
> battery or fails to communicate or a fire zone has a fault. If the zone
is
> bypassed simply unbypass it.
> The instructions for keypad operation are on the inside of the door.

Probably low battery than because of power outage during hurricane. This
isn't a customer but a call in. I'll set up a service call if they want or
just see if the battery charges back up. Thanks for the information.

Bob W.




Similar ThreadsPosted
Aritech / Transport PC October 3, 2006, 2:31 pm
Aritech GS 610 Shock Sensor May 5, 2008, 5:27 am

The site map in XML format XML site map

Contact Us | Privacy Policy