|
Posted by SantaUK on March 15, 2008, 8:49 am
If you were Registered and logged in, you could reply and use other advanced thread options
I have an ADT Galaxy keypad that I am going to fit on a system install for a
friend. Its the same one as in this picture on www.ebay.co.uk Item number
330218907773
Its the one that you can press * and 2, * and 5, * and 8 to summon
assistance from the Police Fire etc. I have tried hooking it up to my
system, and can't for the life of me figure out how to configure this
function. I'm assuming it triggers an output, and you could use the links
section to signal any other indicators. Anyone got any advice for getting
these going?
Regards
SantaUK
|
|
Posted by Jim Rojas on March 15, 2008, 9:17 am
If you were Registered and logged in, you could reply and use other advanced thread options
If it is like the USA versions, you must program the corresponding
zones. Zone 95, 96 and 99.
Jim Rojas
SantaUK wrote:
> I have an ADT Galaxy keypad that I am going to fit on a system install for a
> friend. Its the same one as in this picture on www.ebay.co.uk Item number
> 330218907773
>
> Its the one that you can press * and 2, * and 5, * and 8 to summon
> assistance from the Police Fire etc. I have tried hooking it up to my
> system, and can't for the life of me figure out how to configure this
> function. I'm assuming it triggers an output, and you could use the links
> section to signal any other indicators. Anyone got any advice for getting
> these going?
>
> Regards
>
> SantaUK
>
>
>
--
Posted via a free Usenet account from http://www.teranews.com
|
|
Posted by SantaUK on March 15, 2008, 10:38 am
If you were Registered and logged in, you could reply and use other advanced thread options
mmmm, makes sense, think I'll dig into the manual on that one.
> If it is like the USA versions, you must program the corresponding zones.
> Zone 95, 96 and 99.
>
> Jim Rojas
>
>
>
> SantaUK wrote:
>> I have an ADT Galaxy keypad that I am going to fit on a system install
>> for a
>> friend. Its the same one as in this picture on www.ebay.co.uk Item
>> number
>> 330218907773
>>
>> Its the one that you can press * and 2, * and 5, * and 8 to summon
>> assistance from the Police Fire etc. I have tried hooking it up to my
>> system, and can't for the life of me figure out how to configure this
>> function. I'm assuming it triggers an output, and you could use the
>> links
>> section to signal any other indicators. Anyone got any advice for
>> getting
>> these going?
>>
>> Regards
>>
>> SantaUK
>>
>>
>>
>
> --
> Posted via a free Usenet account from http://www.teranews.com
>
|
|
Posted by Mark Leuck on March 15, 2008, 10:45 am
If you were Registered and logged in, you could reply and use other advanced thread options
> I assume you may mean the outputs belonging to the individual keypad....
> mmmm, makes sense, think I'll dig into the manual on that one.
>
>
>
> > If it is like the USA versions, you must program the corresponding
zones.
> > Zone 95, 96 and 99.
> >
> > Jim Rojas
> >
> >
> >
> > SantaUK wrote:
> >> I have an ADT Galaxy keypad that I am going to fit on a system install
> >> for a
> >> friend. Its the same one as in this picture on www.ebay.co.uk Item
> >> number
> >> 330218907773
> >>
> >> Its the one that you can press * and 2, * and 5, * and 8 to summon
> >> assistance from the Police Fire etc. I have tried hooking it up to my
> >> system, and can't for the life of me figure out how to configure this
> >> function. I'm assuming it triggers an output, and you could use the
> >> links
> >> section to signal any other indicators. Anyone got any advice for
> >> getting
> >> these going?
> >>
> >> Regards
> >>
> >> SantaUK
> >>
> >>
> >>
> >
> > --
> > Posted via a free Usenet account from http://www.teranews.com
> >
>
>
|
|
Posted by SantaUK on March 15, 2008, 12:17 pm
If you were Registered and logged in, you could reply and use other advanced thread options
enable this function, and I don't have an ADT version of the manual, only
the original manufacturer version. Unfortunately the keypad only has output
number *99 - so no joy on that score. And I can't seem to see anything
where you can press * and a number, either together or separately, in the
manual.
> You didn't bother digging into the manual the first time?
>
>
>> I assume you may mean the outputs belonging to the individual keypad....
>> mmmm, makes sense, think I'll dig into the manual on that one.
>>
>>
>>
>> > If it is like the USA versions, you must program the corresponding
> zones.
>> > Zone 95, 96 and 99.
>> >
>> > Jim Rojas
>> >
>> >
>> >
>> > SantaUK wrote:
>> >> I have an ADT Galaxy keypad that I am going to fit on a system install
>> >> for a
>> >> friend. Its the same one as in this picture on www.ebay.co.uk Item
>> >> number
>> >> 330218907773
>> >>
>> >> Its the one that you can press * and 2, * and 5, * and 8 to summon
>> >> assistance from the Police Fire etc. I have tried hooking it up to my
>> >> system, and can't for the life of me figure out how to configure this
>> >> function. I'm assuming it triggers an output, and you could use the
>> >> links
>> >> section to signal any other indicators. Anyone got any advice for
>> >> getting
>> >> these going?
>> >>
>> >> Regards
>> >>
>> >> SantaUK
>> >>
>> >>
>> >>
>> >
>> > --
>> > Posted via a free Usenet account from http://www.teranews.com
>> >
>>
>>
>
>
|
| Similar Threads | Posted | | Galaxy 512 | November 29, 2005, 2:16 pm |
| Ademco Galaxy 16 plus | August 15, 2006, 6:14 pm |
| Galaxy 16+ Engineer Code | September 19, 2005, 3:19 pm |
| Galaxy 8 installation manual | March 8, 2006, 4:56 pm |
| Galaxy 60 code needed ... | November 18, 2007, 11:59 am |
| Honeywell Galaxy Panels | April 1, 2008, 4:07 pm |
| galaxy 3-520 comms fails on sia | August 9, 2008, 9:29 pm |
| Galaxy Alarm - Engineer / Installer Manual WANTED | September 16, 2006, 11:40 am |
| Keypad | August 26, 2005, 11:39 am |
| Need help adding a keypad | August 1, 2005, 10:26 am |
|
XML site map